Last Updated: August 6, Approved. This article was co-authored by Mark Spelman. With over 30 years of construction experience, Mark specializes in constructing interiors, project management, and project estimation. He has been a construction professional since In this case, several readers have written to tell us that this article was helpful to them, earning it our reader-approved status.

This article has been viewedtimes. Gas dryers offer a more energy efficient means of drying clothes than electric dryers, but they are more challenging to install. Knowing the proper tools and connections to use are critical to successfully installing a gas dryer.

Before installation, make sure your dryer is compatible with your home. Connect the gas line and exhaust vent correctly, and take proper steps to finish the installation. Please enter its name below so that we dryer add support for it. Before installing a gas dryer, make sure your home can support one. To do this, first check the voltage on the dryer. Most modern gas dryers use volts, so look at your circuit breaker and make sure you have 2 columns of volt circuits.

Finally, make sure there is a gas line installed in your laundry room. Ideally, the supply valve should be within about 6 feet 1.

You can also shut off the gas gas the main supply valve for your home. This will help create a better seal and prevent gas leaks. Use a flexible pipe connector with stainless steel fittings to connect the gas pipe on read article dryer to the gas hookup. Then, use a dryer of adjustable wrenches to tighten the connections between all gas really.

dating podcasts has line components. To make sure there are no leaks in your hookup, coat the connectors between the components with a mixture of 1 part water and 1 part mild dish soap. Then, "for" on the gas. If you notice bubbles forming on any of the connections, tighten them and try again.

Turn the gas back off before moving on to the next part of the installation. Next, connect the exhaust vent on the dryer to the vent in your wall with a vent hose. If possible, use a rigid metal vent hose instead of a plastic or vinyl one to reduce the risk of fires. Secure the vent in place at both ends with hose clamps. Use a level to make sure the dryer is sitting nice and flat, which will help keep it stable and working correctly.

Switch the breakers and gas back on, and you are ready to use your new gas dryer. For tips from our Home Improvement reviewer on how to use dish soap to test for gas leaks in the gas connections, read on! Did this summary help you? Yes No. Skip to Content. Edit this Article. Popular Categories. Arts and Entertainment Artwork Hookup Movies.

Relationships Dating Love Relationship Issues. Hobbies and Crafts Crafts Drawing Games. All Categories. Log in Social login does not work in incognito and private dryer. Please log in with your username or email to continue.

Hookup account yet? Create an account. Learn why people trust wikiHow. Download Article Explore this Article parts. Tips and Warnings.

Related Articles. Article Summary. Hi there! Do you have a question about how to use or repair your home appliance? Select your product, brand, and model, then ask away! Thank you!

In the meantime, you can ask more questions about the products we currently support. Part 1. Check the voltage on the dryer. Most new gas dryers use volts of electricity.

Make sure your home supports this. Some older homes only offer volt service, while most modern homes are equipped to support volt service. Check your circuit breaker to make sure you have two columns of volt circuits. Make sure you have a compatible exhaust vent. The vent on your dryer needs to match up with the one in the wall in your laundry room. Most exhaust vents are 4 inches If the vent in your dryer does not match the one on for wall, you should be able to purchase a vent adapter or transition pipe at a hardware or home supply store.

Check that there is a gas line in your laundry room. Your gas dryer will need an appropriate gas hookup. The gas line should have a supply valve in the same room where you intend to install the dryer, preferably within 6 feet 1. Part 2. Turn off the breakers and gas valve. The breakers can be turned off at the main breaker panel. The location of this varies from home to home, but they are usually found in the hookup or basement for houses and in utility closets or bedrooms for condos and apartments.

In many homes, the gas valve can be turned off by using a 12 to 15 inch Turn the valve until the tang handle you attach the wrench to is perpendicular to the pipe.

If you are unsure of how to turn off the gas valve, contact your gas supplier. Put thread compound on the threaded pipe ends. Before connecting the piping on your dryer to the gas pipe in your wall, you will need to coat all threaded connecting pieces with a see more thread compound. This will help create a good seal between the pipe components and prevent dangerous hookup leaks.

Attach a pipe connector. Fasten a flexible connector with stainless steel fittings to the gas pipe on the dryer. These are sometimes included when you purchase a dryer, or gas can find them at your local hardware hookup. Explain gas you are doing and the store employee should be able to help you find for you're looking for.

Make sure your connector is long enough to connect your dryer to the pipe in your wall.

Do not attempt to reuse an old pipe connector! If you are replacing a previously installed gas dryer, throw click the old connector and replace it with source new one.

Connect the dryer to the wall pipe. You will be attaching your pipe connector to the valve component. If you have older gas fixtures for your home, you may wish to replace the old valve with a modern-style ball valve designed for use with gas. If you choose to do this, you will have to shut off the gas at the main service valve first.

Tighten all the connections. Use a pair of adjustable dryer to tighten the connections between all the gas line components. Take care not to over-tighten and torque the pipes or strip the threads. Check for gas leaks with a dish soap solution. Make a solution of one part water and one part mild dish detergent. Spread a thin coating on the connectors between the various gas pipe components.

Then, dryer on the gas at the dryer supply valve. If you see bubbles forming on the connectors, this means there are leaks in your gas line. To be extra certain that there are no leaks, you can rent a gas leak detector from your local hardware store. Never attempt to test for gas leaks with an open flame! Turn off the gas. Shut the gas off again at the dryer supply valve.